Comdial and FXT Bedienungsanleitung

Installing and Using System-to-System Networkingon Impact FXS, Impact FXT, DXP, and DXP Plus SystemsThis publication is applicable to systems using Co

Using Features from Hub to NodeAs well as intercom calling, users can engage other cross-platform call handling features. Refer to Appendix A fora com

Making Outside Calls Across the NetworkRouting Outside Calls in the Same LocalityInstallers can provision the network with outside lines connected onl

Restriction Tables—NodesDialedNumberRestrictionLevelExceptionNumberRouteTableTollGroup@Allow All 2Route Table 2, Route 1—NodesSpecification DefaultLin

Routing Outside Calls from Different LocalitiesIf the networked systems are separated by a wide geographic distance, usually installers arrange to hav

12 – FeaturesIMI89–280 Installing and Using System-to-System NetworkingNode PreparationHub PreparationAt Both Nodes,Group channels 1-23 (contained in

Restriction Tables—Node 1Dialed NumberRestrictionLevelExceptionNumberRouteTableTollGroup@@@@@@@@@ Allow All 21804@@@@@@@ Allow All 31213@@@@@@@ Allow

Restriction Tables—HubDialed NumberRestrictionLevelExceptionNumberRouteTableTollGroup@@@@@@@@@ Allow All 21404@@@@@@@ Allow All 31213@@@@@@@ Allow All

Using Centralized Voice MailOne voice mail system connected to the hub provides voice mail boxes to stations connected to the hub and to allthe node s

Understanding the Pooled Lines Network FeatureDetailing the Line Pooling FeatureThe network line pooling feature is a variation of the traditional lin

Explaining the Line Pooling Call HandlingCalls made through the pooled line feature are in the following sequence (should an internal error occur duri

Comdial® strives to design the features in our communications systems to be fullyinteractive with one another. However, this is not always possible, a

Network ARS Programming with Line PoolingWhen programming Automatic Route Selection on a networked system, follow these guidelines:•Program toll restr

Hub Toll/ARS ProgrammingNumberRestrictionLevelExceptionNumberRouteTableToll Group1. 0 Allow all 0 4 12. 1@@@@@@@@@ Allow all 0 4 13. 911 Allow all 0 1

Route Table 3Line GroupRouteAccessModify Table SurchargeTier 1CostTier 1TimeTier 2CostRoute Status1. 12 1 1 $0.00 $0.00 0 Sec $0.00 Active2. 3 1 2 $0.

Node 1 Toll/ARS ProgrammingNumberRestrictionLevelExceptionNumberRouteTableToll Group1. 0 Allow all 0 1 12. 1@@@@@@@@@ Allow all 0 1 13. 911 Allow all

Node 2 Toll/ARS ProgrammingNumberRestrictionLevelExceptionNumberRouteTableToll Group1. 0 Allow all 0 1 12. 1@@@@@@@@@ Allow all 0 1 13. 911 Allow all

Using DID, DNIS, and ANI Features through the NetworkThe DXP, DXP Plus, and FX Series systems provide the DID, DNIS, and ANI support as part of their

RemoteExtensionLocalExtensionExpected ResultsDirect Delay Direct DelayRemote routing one at a time with local assignments ignored501 502 401 402 Only

Feature LimitationsTo avoid race conditions and routing complexity, the following limitations are necessary with the networkincoming call routing feat

Notes

InstallingSystem-to-System NetworkingInstalling the network requires a complete understanding of the elements discussed in the following paragraphs.Fu

Contents1 Introducing System-to-System Networking...3Detailing the Related Publications ...

4. Each node site requires a synchronization card (DXOPT-SYN); however, this is not a requirement at thehub site.NOTE: If you also have the hub connec

4. Determine all the extension numbers for each node and the hub, and determine which extension numbersare to be accessible through the network.5. Iso

Configuring the DXNET or FXNET BoardThe DXNET or FXNET boards require unique strap switch settings for network operation. Depending uponwhether the in

Installation – 31Installing and Using System-to-System Networking IMI89–280T1002gDiagnosticSwitchesSW1SW2LIULocating the DIP Switches(DXNET Board Show

Notes

ProgramingSystem-to-System NetworkingUsing the Visual Man-Machine Interface (VMMI), program the network features at the hub system. You cannotprogram

Programming the Hub SystemNOTE: The nodes will synchronize 3 to 5 minutes after you disconnect VMMI from the hub system.1. Make the necessary programm

Node ConfigurationUse this option to define the hub and the nodes that the network will use.EnabledEnable or disable the hub at each node for networki

Arranging for Line Pooling1. Program the link channels for each node into their own line group. Be sure to isolate the link channelsfrom any other lin

Supporting QSIG Networking ProtocolWith software 15A and later, system-to-system networking supports QSIG networking protocol. With QSIGsupport, Comdi

4 Programing System-to-System Networking...33Programming the Node System ...33

Programming for Network Incoming Call RoutingWhile installers use the PROGRAMMING/STATIONS menu to program local ringing modes, they programremote rin

TI_PRI Flash UpgradePlace the two T1 boards in DXP, DXP Plus or in a FX cabinet. However, when placing T1 boards in a DXPcabinet there are a couple of

Using System-to-System NetworkingThis section discusses the following features:•release link transfer,•conferencing,•intercom calling,•call forwarding

Dialing Intercom NumbersIntercom dialing is the same for both intra- and inter-node systems. The network system verifies the number asvalid and return

Setting Call BackDuring network intercom calls, if a calling station encounters DND, RNA, or busy signals at the called station, thecaller can activat

Appendix A—Feature Networking SupportFeature NameTypeOriginating/Terminating/BothRemoteNetworkingSupportFeatureParametersProgramFeatureAbandoned Hold

Feature NameTypeOriginating/Terminating/BothRemoteNetworkingSupportFeatureParametersProgramFeatureCall Forward AllImmediateTerminating Comdial Across

Feature NameTypeOriginating/Terminating/BothRemoteNetworkingSupportFeatureParametersProgramFeatureHunt Group (can accessHunt group across Networkbut m

Feature NameTypeOriginating/Terminating/BothRemoteNetworkingSupportFeatureParametersProgramFeatureQuick Transfer Terminating ComdialAcross Network(wit

Feature NameTypeOriginating/Terminating/BothRemoteNetworkingSupportFeatureParametersProgramFeatureTrunk to Trunk Transfer Both Comdial Across NetworkV

IntroducingSystem-to-System NetworkingSystem-to-system networking connects several DXP, DXP Plus, or Impact FXS/FXT systems together in anarrangement

Notes

Appendix B—Maintenance ChecklistSystem Software HUB ENG Node FLR Node PUR NodeUnzip new software in the storage directory.Keep zip file - as insurance

Databases HUB ENG Node FLR Node PUR NodeCreate a storage directory in the appropriatedisk area, using the appropriate namingconvention.Archive the dat

IndexAANI... 23ARS ... 16,17,33,36ARS Programming with Line Pooling ... 18Bbootloader...

NnetworkARS... 16communications ... 3DID, DNIS, and ANI ... 23equipment ...

This manual has been developed by Comdial Corporation (the “Company”) and is intended for the useof its customers and service personnel. The informati

IMI89–280.04 05/00printed in U.S.A.

NOTE: With digital service, there is always confusion about what the term line denotes. Since there areactually multiple lines in one digital line, th

Using System-to-System Networking – 5Installing and Using System-to-System Networking IMI89–280HubSystemHub System StationNodeSystemNode System Statio

Notes

Understanding System-to-System Networking FeaturesCurrently, system-to-system networking provides the following joint activities with the hub and all